Matrix E1x Specifikace

E1X ELLIPTICALSERVICE MANUAL

6CHAPTER 3: PREVENTATIVE MAINTENANCE3.3 CARE AND MAINTENANCE INSTRUCTIONSIn order to maximize life span, and minimize down time, all MATRIX equipment

7CHAPTER 4: CONSOLE OVERLAY AND WORKOUT DESCRIPTION4.1 CONSOLE DESCRIPTIONA. WORKOUT PROFILE WINDOW: During a workout, this window displays shapes, m

8CHAPTER 4: CONSOLE OVERLAY AND WORKOUT DESCRIPTION4.2 WORKOUT OVERVIEWPROGRAM NAMEDESCRIPTION DEFAULT TIMEPROMPT INPUTQUICK START Quick Start is the

94.2 WORKOUT OVERVIEW - CONTINUEDWORKOUT TIPS1. Matrix Fitness strongly recommends seeing your physician for a complete physical examination before be

10CHAPTER 4: CONSOLE OVERLAY AND WORKOUT DESCRIPTION4.3 WORKOUT SETUP STEPS - CONTINUEDRANDOM HILL1) Repeatedly press the INTERVAL+ key to select Ran

114.3 WORKOUT SETUP STEPS - CONTINUEDCHAPTER 4: CONSOLE OVERLAY AND WORKOUT DESCRIPTIONAge-Rating Very Poor Poor Fair Good Excellent Superior15-19 <

12The Manager's Custom Mode allows the club owner to customize the elliptical trainer for the club. 1) To enter Manager Mode, press and hold do

13CHAPTER 5: MANAGER MODECUSTOM SETTINGSDEFAULT MINIMUM MAXIMUM UNIT DESCRIPTIONMAXIMUM TIME 60 5 95 MINUTEMaximum workout duration.DEFAULT TIME 60 5

14CHAPTER 6: TROUBLESHOOTING6.1 ELECTRICAL DIAGRAMSELECTRICAL BLOCK DIAGRAM

15WIRING DIAGRAM INSTRUCTION6.1 ELECTRICAL DIAGRAMSCHAPTER 6: TROUBLESHOOTING

16CHAPTER 6: TROUBLESHOOTING P01 - CONSOLE CABLE6.1 ELECTRICAL DIAGRAMS

176.1 ELECTRICAL DIAGRAMSCHAPTER 6: TROUBLESHOOTINGP02-PULSESENSORWIRE

186.1 ELECTRICAL DIAGRAMSP03 - GENERATOR WIRECHAPTER 6: TROUBLESHOOTING

19CHAPTER 6: TROUBLESHOOTING 6.2 TROUBLESHOOTING - CONSOLE POWER ISSUESNO DISPLAY ON THE CONSOLE OR THE DISPLAY IS DIMPOSSIBLE CAUSES:1) The console

206.3 TROUBLESHOOTING - KEYPAD ISSUESCHAPTER 6: TROUBLESHOOTINGALL OR SOME OF THE FUNCTION KEYS DO NOT RESPONDPOSSIBLE CAUSES:1) The keypad connectin

216.4 TROUBLESHOOTING - RESISTANCE ISSUESNO RESISTANCE CHANGE OR ALWAYS HIGH RESISTANCECHAPTER 6: TROUBLESHOOTINGPOSSIBLE CAUSES:1) The console is da

226.5 TROUBLESHOOTING - PEDAL SLIPPINGSLIPPING WHILE PEDALINGCHAPTER 6: TROUBLESHOOTINGPOSSIBLE CAUSES1) Belt tension is not enough.2) The one way b

236.6 TROUBLESHOOTING - NOISE ISSUESKNOCKING OR CREAKING NOISESCHAPTER 6: TROUBLESHOOTINGPOSSIBLE CAUSES:1) The pedal is connected to the link arm to

246.7 TROUBLESHOOTING - HEART RATE ISSUESHEART RATE DOES NOT WORKCHAPTER 6: TROUBLESHOOTINGPOSSIBLE CAUSES:1) There is not a good contact between the

257.1 FRONT SHROUD REMOVAL1) Remove the 18 screws holding the shrouds in place using a #2 Phillips Screwdriver. 2) There should be 8 screws on the

CHAPTER 1: SERIAL NUMBER LOCATION ... 1CHAPTER 2: IMPORTANT SAFETY INSTRUCTIONS 2.1

267.2 CONSOLE REPLACEMENT1) Remove the 4 screws holding the console to the frame (Figure A & B).2) Disconnect the console cable, HR, and level w

277.3 HEART RATE HANDLEBAR REPLACEMENT1) Remove the 4 screws holding the heart rate handlebar to the console mast being careful to support the handle

28CHAPTER 7: PART REPLACEMENT GUIDE 7.4 HEART RATE GRIPS REPLACEMENT1) Using a flat screwdriver, pry the silver metal heart rate plate away from the

297.5 CUP HOLDER REPLACEMENTCHAPTER 7: PART REPLACEMENT GUIDE 1) Remove the 2 screws holding the cup holder to the console mast (Figure A). 2) Remo

30CHAPTER 7: PART REPLACEMENT GUIDE 7.6 CONSOLE KEYPAD / OVERLAY REPLACEMENT 1) Remove the console as outlined in Section 7.2. 2) Remove the 6 scre

317.6 CONSOLE KEYPAD / OVERLAY REPLACEMENT - CONTINUEDCHAPTER 7: PART REPLACEMENT GUIDE FIGURE E FIGURE F6)Disconnecttheappropriateribboncablef

321) Remove the front shrouds as outlined in Section 7.1. 2) Disconnect the 3 wire connections to the lower board (Figure A). 3) Remove the 2 scr

337.8 DRIVE BELT REPLACEMENTCHAPTER 7: PART REPLACEMENT GUIDE 1) Remove the front shrouds as outlined in Section 7.1. 2) Remove the idler tension ey

347.9 ECB (ELECTRONIC BRAKE) BELT REPLACEMENTCHAPTER 7: PART REPLACEMENT GUIDE 1) Remove the front shrouds as outlined in Section 7.1. 2) Loosen th

357.10 ECB (ELECTRONIC BRAKE) REPLACEMENT CHAPTER 7: PART REPLACEMENT GUIDE1) Remove the front shrouds as outlined in Section 7.1. 2) Disconnect th

ivTABLE OF CONTENTS7.16 Link Arm Replacement ... 447

36FIGURE EFIGURE F6) Remove the screw holding the ECB wire harness in place (Figure E). 7) Remove the defective ECB (Figure F). 8)ReverseSteps

377.11 CRANK AXLE SET REPLACEMENTCHAPTER 7: PART REPLACEMENT GUIDE1) Remove the front shrouds as outlined in Section 7.1. 2) Remove the drive belt

38CHAPTER 7: PART REPLACEMENT GUIDE7.12 DRIVE AXLE SET REPLACEMENT1) Remove the front shrouds as outlined in Section 7.1. 2) Remove the drive belt

397.12 DRIVE AXLE SET REPLACEMENT - CONTINUEDCHAPTER 7: PART REPLACEMENT GUIDEFIGURE EFIGURE FFIGURE G FIGURE H6) Remove the screw / nut holding the

407.13 LEVEL BUTTON ASSEMBLY REPLACEMENTCHAPTER 7: PART REPLACEMENT GUIDE 1) Remove the 2 screws holding the level button assembly to the dual action

417.14 DUAL ACTION HANDLEBAR REPLACEMENTCHAPTER 7: PART REPLACEMENT GUIDE 1) Remove the two caps covering the screw / nut holding the dual action han

42FIGURE EFIGURE F4) Remove the 4 screws holding the dual action handlebar to the pivot tube (Figure E). 5) You can now remove the dual action hand

437.15 PEDAL REPLACEMENTCHAPTER 7: PART REPLACEMENT GUIDE 1) Remove the 4 screws holding the link arm assembly to the pedal arm (Figure A). 2) Remo

447.16 LINK ARM REPLACEMENT CHAPTER 7: PART REPLACEMENT GUIDE 1) Remove the two caps covering the screw / nut holding the dual action handlebar to th

457.16 LINK ARM REPLACEMENT - CONTINUEDCHAPTER 7: PART REPLACEMENT GUIDE FIGURE E FIGURE FFIGURE G FIGURE H4) Remove the 3 screws holding the pedal

11.1 SERIAL NUMBER LOCATIONCHAPTER 1: SERIAL NUMBER LOCATION

467.17 PEDAL ARM REPLACEMENT CHAPTER 7: PART REPLACEMENT GUIDE 1) Remove the front shrouds as outlined in Section 7.1.2) Pull the cap off of the cra

47FIGURE E7.17 PEDAL ARM REPLACEMENT - CONTINUEDCHAPTER 7: PART REPLACEMENT GUIDE FIGURE F5) Remove the 4 screws holding the link arm assembly to the

48FIGURE HFIGURE IFIGURE J FIGURE K7) Remove the 5 screws holding down the roller cover, remove the cover (Figure I). 8) Move the pedal arm so that

497.18 REAR ROLLER REPLACEMENTCHAPTER 7: PART REPLACEMENT GUIDE 1)FollowSteps1-8fromSection7.17toremovethepedalarm.2) Remove the screw

507.19 ROLLER TRACK REPLACEMENT1)FollowSteps1-8fromSection7.17toremovethepedalarm.2) Remove the 8 screws holding down the covering plate

51CHAPTER 7: PART REPLACEMENT GUIDE 7.20 FRONT ROLLER REPLACEMENT1) Remove the screw holding the front roller to the stabilizer (Figure A). 2) Remo

52ONCE THE UNIT OR REPLACEMENT PART IS FULLY INSTALLED AND ASSEMBLED AND PROPERLY PLACED ON THE FLOOR, USE THE FOLLOWING INSTRUCTIONS TO TEST THE MACH

53CHAPTER 8: ELLIPTICAL TRAINER SPECIFICATIONS AND ASSEMBLY GUIDE8.1 ELLIPTICAL SPECIFICATIONSCONSOLEDisplay Screen WorkoutProfileWindow-7"b

548.2 UNPACKING THE ELLIPTICAL TRAINERCHAPTER 8: ELLIPTICAL TRAINER SPECIFICATIONS AND ASSEMBLY GUIDEThe Matrix E1x Elliptical Trainer is carefully in

558.3 FASTENERS AND ASSEMBLY TOOLSCHAPTER 8: ELLIPTICAL TRAINER SPECIFICATIONS AND ASSEMBLY GUIDE

2CHAPTER 2: IMPORTANT SAFETY INSTRUCTIONS 2.1 BEFORE GETTING STARTEDThe Matrix E1x Elliptical Trainer is intended for commercial use. To ensure your

568.4 ASSEMBLY INSTRUCTIONSGETTING STARTEDRead the owner's manual before setting up the Matrix E1x Elliptical Trainer. Place the unit where it w

571) LIft up the Main Body at the front end. Insert a wooden or hard box underneath the Main Body while you lift it up. 2) Fasten the Front Foot to

588.4 ASSEMBLY INSTRUCTIONS - CONTINUEDCHAPTER 8: ELLIPTICAL TRAINER SPECIFICATIONS AND ASSEMBLY GUIDECONSOLE MAST1) Thread the Console Mast through

598.4 ASSEMBLY INSTRUCTIONS - CONTINUEDCHAPTER 8: ELLIPTICAL TRAINER SPECIFICATIONS AND ASSEMBLY GUIDEHR HANDLEBAR1) Plug in the heart rate wires to

608.4 ASSEMBLY INSTRUCTIONS - CONTINUED1) Attach the Dual Action Handlebars (R) and (L) to the Console Mast using eight screws (Z18), and place the h

61CHAPTER 8: ELLIPTICAL TRAINER SPECIFICATIONS AND ASSEMBLY GUIDE8.4 ASSEMBLY INSTRUCTIONS - CONTINUED

628.5 LEVELING THE ELLIPTICALCHAPTER 8: ELLIPTICAL TRAINER SPECIFICATIONS AND ASSEMBLY GUIDESTABILIZING THE MATRIX E1X ELLIPTICAL TRAINERAfterplacing

631) Remove the 4 screws and plate from the front side of the console mast (Figure A). 2) Fish the TV power wire and coax cable from within the con

64FIGURE E FIGURE FFIGURE GFIGURE H8.6 TV BRACKET INSTALLATION - CONTINUEDCHAPTER 8: ELLIPTICAL SPECIFICATIONS AND ASSEMBLY GUIDE

65FIGURE I FIGURE JFIGURE K FIGURE LCHAPTER 8: ELLIPTICAL SPECIFICATIONS AND ASSEMBLY GUIDE8.6 TV BRACKET INSTALLATION - CONTINUED

3CAUTION! If you experience chest pains, nausea, dizziness, or shortness of breath, stop exercising immediately and con-sult your physician before co

66NOTES

67MATRIX FITNESS SYSTEMS CORP.1610 LANDMARK DRIVE COTTAGE GROVE WI 53527 USATOLL FREE 866.693.4863 www.matrixfitness.com FAX 608.839.1717KOREV. 1

4CHAPTER 2: IMPORTANT SAFETY INSTRUCTIONS 2.3 ELECTRICAL REQUIREMENTSSELF POWERED FEATURES:On the Matrix E1x Elliptical Trainer, the users pedaling ge

5Preventative maintenance and daily cleaning will prolong the life and look of your MATRIX E1x Elliptical TrainerPlease read and follow these tips.•