Matrix E3x Servisní příručka

E 3 X - 0 2 S U S P E N S I O N E L L I P T I C A L S E R V I C E M A N U A L

7CHAPTER 4: CONSOLE OVERLAY AND WORKOUT DESCRIPTIONGO - Press to immediately begin a workout. Workout, resistance level, and time will automatically

8CHAPTER 4: CONSOLE OVERLAY AND WORKOUT DESCRIPTION4.5 WORKOUT SETUP STEPS - HEART RATE CONTROLTARGETHEARTRATE - The Matrix Ascent Trainer comes wit

9The Manager's Custom Mode allows the club owner to customize the Suspension Elliptical for the club. 1) To enter Manager Mode, press and hold

105.2 MANAGER MODE INFORMATION CUSTOM SETTING DEFAULT MINIMUM MAXIMUM DESCRIPTIONMaximum Time 60 min 5 min 99 min Sets the total run time of any prog

116.1 USING ENGINEERING MODETo enter Engineering Mode, hold the LEVEL UP and DOWN keys for 3-5 seconds until Manager appears on the middle LED display

127.1 USING SERVICE MODETo enter Service Mode, hold the LEVEL UP and DOWN keys for 3-5 seconds until Manager Mode appears on the middle LED display.

138.1 ELECTRICAL DIAGRAMSCHAPTER 8: TROUBLESHOOTING

148.1 ELECTRICAL DIAGRAMS - CONTINUEDG14 - HAND PULSE CONNECTION WIRECHAPTER 8: TROUBLESHOOTING

158.1 ELECTRICAL DIAGRAMS - CONTINUEDCHAPTER 8: TROUBLESHOOTINGP21 - DIGITAL COMMUNICATION WIRE

168.2 ERROR CODES ON THE CONSOLECODE CLASS DESCRIPTION SOLUTION0x02AB C Machine type error. Set the correct machine type in Engineering Mode. 0x02B4

CHAPTER 1: SERIAL NUMBER LOCATION ... 1CHAPTER 2: IMPORTANT SAFETY INSTRUCTIONS 2.1 Read and

178.3 LCB LED INDICATORSLED CHECKPOINT POSSIBLE ISSUE SOLUTIONLEDs 2, 3, 4, 6, & 7 should be ON. If they are OFF, the LCB is damaged. Replace th

18ERROR 0x04A0 (DIGITAL COMMUNICATION FAILURE) LED 1SYMPTOM: Error code 0x04A0 is displayed on the console. CHECK POINT POSSIBLE ISSUE SOLUTIONLED

19HIGH OR NO RESISTANCEPOSSIBLE CAUSES:1) The console cable is damaged or not properly plugged in. 2) The UCB is damaged. 3) The Generator is dam

20PEDALS SLIPPINGPOSSIBLE CAUSES:1) The belt tension is not enough. 2) The one way bearing is damaged. SOLUTION:1) Remove the covers and check th

21HEART RATE ISSUESPOSSIBLE CAUSES:1) The display is stuck on heart rate. 2) Erratic heart rate. 3) No heart rate. SOLUTION:1) If the display is

228.9 TROUBLESHOOTING - NO POWER TO THE CONSOLEPOWER SWITCH IS ON, BUT THE CONSOLE HAS NO DISPLAYPOSSIBLE CAUSES:1) The unit is not getting power fro

239.1 FRONT DISK REPLACEMENT 1) Remove the center cover by turning it counter clockwise (Figures A & B). 2) Remove the 3 screws holding the dis

249.2 FRONT SHROUD REPLACEMENT 1) Remove the link arm and pedal arm plastic caps (Figures A & B). 2) Detach the dual action handlebar from the

259.2 FRONT SHROUD REPLACEMENT - CONTINUED7)Pullouttherubbertrayfromthecupholderplastic(gureG).8) Remove the 2 screws to disassemble

269.2 FRONT SHROUD REPLACEMENT - CONTINUED12) Remove the 9 screws to detach the front shrouds from the frame (or each other) (Figure M). 13) Turn t

III9.14 Foot Pedals Replacement ... 539.15 Pedal Arm Replace

279.3 LOWER CONTROL BOARD REPLACEMENT1) Turn off the power and disconnect the cord from the machine.2) Remove both front disks from the machine as

289.4 GENERATOR REPLACEMENT1) Turn off power and disconnect the cord from the machine.2) Remove the front disks as outlined in Section 9.1. 3) Re

299.4 GENERATOR REPLACEMENT – CONTINUED FIGURE E FIGURE F8) Remove the nut from the other side of the generator bracket (Figure E). 9) Loosen and r

309.5 GENERATOR BELT REPLACEMENT1) Turn off the power and disconnect the cord from the machine. 2) Remove the front disks from the machine as outli

319.6 DRIVE BELT REPLACEMENT1) Turn off the power and disconnect the cord from the machine. 2) Remove the front disks from the machine as outlined

329.7 PULLEY AXLE SET REPLACEMENT1) Turn off the power and disconnect the cord from the machine. 2) Remove both front disks from the machine as out

339.8 DRIVE AXLE SET REPLACEMENTNOTE:AMatrixspecialtoolisneededtocorrectlyreplaceadriveaxle.Orderpart#0000094817fromMatrixCTSat

349.8 DRIVE AXLE SET REPLACEMENT - CONTINUED10) The drive axle should have come with an iron plate installed (Figure G). 11) Assemble the Matrix to

359.8 DRIVE AXLE SET REPLACEMENT - CONTINUED16) Turn the nut until the iron plate is close to the frame on the right side (Figure M). 17) Remove th

369.8 DRIVE AXLE SET REPLACEMENT - CONTINUED22) Use a screwdriver to remove the iron plate from the drive axle (Figures S & T). 23) Re-install

11.1 SERIAL NUMBER LOCATIONSERIAL NUMBER LOCATIONCHAPTER 1: SERIAL NUMBER LOCATION

379.9 CRANK REPLACEMENT1) Turn off the power and disconnect the cord from the machine. 2) Remove the front disks from the machine as outlined in Se

389.10 CONSOLE REPLACEMENTCHAPTER 9: PART REPLACEMENT GUIDE1) Turn off the power and disconnect the cord from the machine. 2) Remove the 5 screws

399.11 OVERLAY & KEYPAD REPLACEMENTNOTE: The instructions below are for console overlays / keypads, but the procedure is the same regardless of w

409.11 KEYPAD & OVERLAY REPLACEMENT - CONTINUEDFIGURE E FIGURE FFIGURE G7) Peel part of the protective film from the back of the overlay (Figure

419.12 CONSOLE MAST HANDLEBAR REPLACEMENT1) Turn off the power and disconnect the cord from the machine. 2) Remove the 4 bolts that hold the handl

429.13 DUAL ACTION HANDLEBAR REPLACEMENT1) Remove the plastic cover where the dual action handlebar meets the link arm (Figure A). 2) Remove the bo

439.14 FOOT PEDALS REPLACEMENT1) Pull up on and remove the rubber portion of the pedal (Figure A). 2) Remove the 4 screws that hold the plastic pe

449.15 PEDAL ARM REPLACEMENT1) Remove the plastic cover where the pedal arm attaches to the crank (Figure A). 2) Disconnect the pedal arm from the

459.16 LINK ARM REPLACEMENT1) Remove the plastic cover where the dual action handlebar meets the link arm (Figure A). 2) Remove the bolt and bushin

469.17 SWING ARM REPLACEMENT1) Remove the bolt from the upper pivot joint on the swing arm (Figure A). 2) Remove the plastic cap from the swing arm

22.1 READ THESE INSTRUCTIONSThis Suspension Elliptical is intended for commercial use. To ensure your safety and protect the equipment, read al

479.18 VERTICAL STABILIZER ARM REPLACEMENT1) Remove the bolt that holds the vertical stabilizer arm to the frame (Figures A & B). 2) Remove the

489.19 INCLINE ARM COVER REPLACEMENT1) Remove the screw that holds the plastic cover on the arm (Figures A & B). 2) Remove the incline arm cove

499.20 HANDLEBAR SERVICE1) All items on the handlebar are removed using a Phillips screwdriver from the underside of the bar. 2) Once the screws ar

509.21 TESTING THE SUSPENSION ELLIPTICALONCE THE UNIT OR REPLACEMENT PART IS FULLY INSTALLED AND ASSEMBLED AND PROPERLY PLACED ON THE FLOOR, USE THE F

5110.1 SUSPENSION ELLIPTICAL SPECIFICATIONSFEATURESStride Length 21"Incline Range N/AContact and Telemetric Heart Rate Sensors YesCushioned Footp

5210.2 ASSEMBLY HARDWAREQUANTITY SKETCH DESCRIPTION PACKAGE COLOR4 SOCKET HEAD CAP SCREW(M10 X 1.5P X 25L)10.9 GRADE MINIMUMRED (2 BAGS)4 FLAT WASHER(

5310.3 SUSPENSION ELLIPTICAL ASSEMBLY STEPSSTEP 1CHAPTER 10: SUSPENSION ELLIPTICAL SPECIFICATIONS AND ASSEMBLY GUIDE

5410.3 SUSPENSION ELLIPTICAL ASSEMBLY STEPS - CONTINUEDSTEP 2 - RED HARDWARE BAGCHAPTER 10: SUSPENSION ELLIPTICAL SPECIFICATIONS AND ASSEMBLY GUIDE

5510.3 SUSPENSION ELLIPTICAL ASSEMBLY STEPS - CONTINUEDSTEP 3 - PINK HARDWARE BAGCHAPTER 10: SUSPENSION ELLIPTICAL SPECIFICATIONS AND ASSEMBLY GUIDE

5610.3 SUSPENSION ELLIPTICAL ASSEMBLY STEPS - CONTINUEDTorque this bolt to 80 N-m.STEP 4 - GREEN / YELLOW HARDWARE BAGCHAPTER 10: SUSPENSION ELLIPTICA

32.2 ELECTRICAL REQUIREMENTSGROUNDING INSTRUCTIONS:The Matrix E3x-02 Suspension Elliptical must be grounded. If it should malfunction or break down,

5710.3 SUSPENSION ELLIPTICAL ASSEMBLY STEPS - CONTINUEDSTEP 5 - RED HARDWARE BAGCHAPTER 10: SUSPENSION ELLIPTICAL SPECIFICATIONS AND ASSEMBLY GUIDE

5810.3 SUSPENSION ELLIPTICAL ASSEMBLY STEPS - CONTINUEDSTEP 6CHAPTER 10: SUSPENSION ELLIPTICAL SPECIFICATIONS AND ASSEMBLY GUIDE

5910.3 SUSPENSION ELLIPTICAL ASSEMBLY STEPS - CONTINUEDSTEP 7 - BLUE / BLACK HARDWARE BAGCHAPTER 10: SUSPENSION ELLIPTICAL SPECIFICATIONS AND ASSEMBLY

6010.3 SUSPENSION ELLIPTICAL ASSEMBLY STEPS - CONTINUEDSTEP 8 - WHITE HARDWARE BAGCHAPTER 10: SUSPENSION ELLIPTICAL SPECIFICATIONS AND ASSEMBLY GUIDE

6110.3 SUSPENSION ELLIPTICAL ASSEMBLY STEPS - CONTINUEDSTEP 9 - PINK HARDWARE BAGCHAPTER 10: SUSPENSION ELLIPTICAL SPECIFICATIONS AND ASSEMBLY GUIDE

6210.3 SUSPENSION ELLIPTICAL ASSEMBLY STEPS - CONTINUEDSTEP 10 - PINK HARDWARE BAGCHAPTER 10: SUSPENSION ELLIPTICAL SPECIFICATIONS AND ASSEMBLY GUIDE

6310.3 SUSPENSION ELLIPTICAL ASSEMBLY STEPS - CONTINUEDSTEP 11 - PINK HARDWARE BAGCHAPTER 10: SUSPENSION ELLIPTICAL SPECIFICATIONS AND ASSEMBLY GUIDE

6410.3 SUSPENSION ELLIPTICAL ASSEMBLY STEPS - CONTINUEDSTEP 12 - PINK HARDWARE BAGCHAPTER 10: SUSPENSION ELLIPTICAL SPECIFICATIONS AND ASSEMBLY GUIDE

6510.4 LEVELING THE SUSPENSION ELLIPTICALSTABILIZINGTHEMATRIXSUSPENSIONELLIPTICALThe Matrix Suspension Elliptical should be level for optimum use.

6611.1 SOFTWARE UPGRADE PROCEDURECHAPTER 11: SOFTWARE UPGRADE PROCEDURE1) Turn on the power to the Suspension Elliptical, wait until the standard dis

43.1 RECOMMENDED CLEANING TIPS 3.2 CHECK FOR DAMAGED PARTSPreventative maintenance and daily cleaning will prolong the life and look of your MATRIX Su

67NOTES

68MAT RIX FITNE S S S Y STEMS CORP.1610 LAND M ARK DRIVE COTTAGE GROV E WI 53527 USATO L L FRE E 866 . 693.48 6 3 w w w. m a t r i x

53.3 CARE AND MAINTENANCE INSTRUCTIONIn order to maximize life span, and minimize down time, all MATRIX equipment requires regular cleaning, and maint

64.1 CONSOLE DESCRIPTIONCHAPTER 4: CONSOLE OVERLAY AND WORKOUT DESCRIPTIONWORKOUTKEYS Simple program view and selection buttons. GO: One touch Sta